Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
- 11. Body
   11.1. Maintenance and repair
   11.2. Vinyl finishing
   11.3. Upholstery and rugs
   11.4. Repair of insignificant damages of a body
   11.5. Repair of considerable damages of a body
   11.6. Loops and locks
   11.7. Windshield and motionless glasses
   11.8. Cowl
   11.9. Trunk lid
   11.10. A back door (models with a body "Station wagon")
   11.11. Basic rack of a back door
   11.12. Decorative panel of a door
   11.13. Door
   11.14. Door latch, cylinder of the lock and handle
   11.15. Door windowpane
   11.16. Bumpers
   11.17. External mirror
   11.18. Seats
   11.19. Frame of a combination of devices
   11.20. Glove compartment
   11.21. Central decorative panel
   11.22. Casing of a steering column
   11.23. Lower panel of finishing of a steering column
   11.24. Console
   11.25. Dashboard
   11.26. Front grille
   11.27. Ventilating grate of a cowl
   11.28. Seat belts
+ 12. Electric equipment


11.16. Bumpers

GENERAL INFORMATION

Typical parts of a front bumper

1. The forward mudguard located under a wing (right)
2. The forward mudguard located under a wing (left)
3,4. Mudguard
5. Lower protection of the engine (right)
6. Lateral support of a bumper
7. Lower protection of the engine (left)
8. The top strengthening headlight arm element
9. Lateral support of a bumper
11. The strengthening element of a front bumper
12,16. Lateral support of a bumper
13,15. Directing a bumper
14. Absorber of energy of blow of a front bumper
17. Dimensional lamp
18,20. Headlight
19. Front grille
21. Dimensional lamp
22. Covering of a front bumper
23,24. Turn signal bulb

Typical parts of a rear bumper on models with a body like "Sedan"

1. Luggage carrier rug
2. Finishing of a luggage carrier on the right side
3. Back plate of finishing of a floor
4. Finishing of a luggage carrier behind
5. Finishing of a luggage carrier on the left side
6. Top clamp
7. The back combined lamp
8. Absorber of energy of blow of a rear bumper
9. Covering of a rear bumper
10. Bulb of illumination of registration plate
11. The strengthening element of a rear bumper
12. Arm of a rear bumper
13. Lateral clamp
14. Top clamp
15. Lateral support
16. Mudguard
17. Square air duct
18. Mudguard
19. Lateral consolidation

Typical parts of a rear bumper on models with a body like "Station wagon"

1. The strengthening element of a rear bumper
2. Lateral support
3. Covering of a rear bumper
4. Lateral support
5. Top clamp
6. Absorber of energy of blow of a rear bumper
7. Arm of a rear bumper

Removal and installation

PERFORMANCE ORDER
1. Put the car on the parking brake, lift it and reliably fix on goats.
2. Disconnect a wire of "weight" from the accumulator, and also disconnect all wires which can prevent removal of a bumper.
3. Uncover a bumper (if it is established), trying not to damage a cover and a bumper.
4. From under a bottom of the car unscrew fixing bolts of a bumper.
5. Remove a bumper from the car.
6. Installation is made in the return sequence.